Steel banding before the foundation set in the center of the cushion, and cross through the center axis for vertical and horizontal, and then through the center ring for radiation tendons and tendon distance and ring the number.

鋼筋綁扎前，先在墊層上定出基礎中心點欧美性荡视频，并通過中心點定出縱橫十字軸線精品一区在线，再通過中心點定出輻射筋和環筋的距離和環數免费的三级黄网站。

One cycle of operation to take Silo body construction, the construction procedure as follows: steel banding to Silo body gantry beams assembled below -→ one-time pouring concrete 700mm high -→ early slide three trips (that is 75mm high)-→ check off the concrete slipform system appropriate degree and working conditions -→ continue pouring concrete 500mm high -→ then slip trip or three -→ pouring concrete to template missing -→ normal sliding each slide or 500mm high -→ stratified cross - lap steel banding -→ pouring concrete 500mm high -→ Waterloo or 500mm high -→ 4 in accordance with the procedure after Silo body pouring until the completion of cycle.

其中筒身施工采取循環作業18禁免费无码无遮挡网站老男人，其施工程序?yàn)椋航壴采礓摻钪两M裝好的門架橫梁下面—→一次性澆筑混凝土700mm 高—→初滑三個行程（即75mm 高度）—→檢查滑出混凝土合適度及滑模系統工作狀況—→繼續澆筑混凝土500mm 高—→再滑升三個行程—→澆筑混凝土至模板上口—→轉入正彻访夥咽悠担滑升，每次滑升500mm 高—→分層交圈綁扎鋼筋—→澆筑混凝土500mm 高—→滑升500mm 高—→按后四道程序循環往復直至筒身澆筑完成wwwjizzjizzjizz。

One cycle of operation to take construction, the construction procedure as follows: steel banding to gantry beams assembled below -→ one-time pouring concrete 700mm high -→ early slide three trips (that is 75mm high)-→ check off the concrete slipform system appropriate degree and working conditions -→ continue pouring concrete 500mm high -→ then slip trip or three -→ pouring concrete to template missing -→ normal sliding each slide or 500mm high -→ stratified cross - lap steel banding -→ pouring concrete 500mm high -→ Waterloo or 500mm high -→ 4 in accordance with the procedure after pouring until the completion of cycle.

其中筒身施工采取循環作業一级黄片;一被-，其施工程序?yàn)椋航壴采礓摻钪两M裝好的門架橫梁下面—→一次性澆筑混凝土700mm 高—→初滑三個行程（即75mm 高度）—→檢查滑出混凝土合適度及滑模系統工作狀況—→繼續澆筑混凝土500mm 高—→再滑升三個行程—→澆筑混凝土至模板上口—→轉入正尘镁妹夥芽雌患叮滑升，每次滑升500mm 高—→分層交圈綁扎鋼筋—→澆筑混凝土500mm 高—→滑升500mm 高—→按后四道程序循環往復直至筒身澆筑完成女人自慰喷水的网站。

crossband transponder：交叉頻帶發送機

交叉頻帶的 crossband | 交叉頻帶發送機 crossband transponder | 頻率交聯,交向排列 cross-banding