From FEM, the contact stress obeys the semi-ellipse distribution and the Mises stress and shear stress are also consistent with contact mechanics theory, but there exists offset or deflection in the symmetric lines of stress distribution, which originates from tooth bending deformation.

由有限元方法得到的漸開線輪齒的接觸應力符合Hertz理論中的半橢圓分布規律亚洲精品福利网，Mises應力和剪應力分布也符合接觸力學理論QVOD经典激情视频图片小说，但應力分布的對稱中心存在偏離或者偏斜現象免费看所有乱伦黄色视频，分析認為色哟哟WWW网址，是由于輪齒彎曲變形造成的超碰免费公开人妻人人。

At the same time, for the polishing plate of diamond film with the same thickness, von Mises equivalent stress and the radial displament show a ascending tendency with the increase of rotating speed, but the axial displacement firstly increases and then decreases.

同時，對于同一厚度的金剛石膜拋光裝置一级毛片一级毛片AAAA级，隨著轉速的提高一级免费视频国产，von Mises等效應力和徑向位移呈現相似的上升趨勢，軸向位移卻先上升后下降色亚洲插插。

The results show that, for the elasto-plastic contact of tip-substrate approach and separation process, the material plastic yielding in the atomic level is still governed by the von Mises criterion. For the adhesion of flat-ended wedges, continuum mechanics can be still applied down to a few lattice constants within the contact region, and give reasonable results, apart from the discrepancies near the contact edges. Moreover, adhesion hysteresis occurs during unloading due to the atomic steps, where the unloading curve does not coincide with the loading one. This in turn supports the presumption proposed by Pollock for the adhesion of stepped spheres.

本文首先對針尖—基體模型的彈塑性接觸機理進行了深入研究免费人人插操摸，指出在原子水平上材料的塑性屈服仍由Von Mises準則控制；對平底錐沖頭粘著接觸的模擬表明久精品91区热，除了在接觸區邊緣附近有一定差別外黄片免费在线看吗，接觸力學方法在接觸區內幾個晶格常數范圍內仍能給出令人滿意的結果；由于原子臺階效應国产一级无码AV片在线看，加載與卸載曲線不重合免费三级性毛毛片，出現粘著滯后，證實了Pollock關于具有納米階梯結構的球體粘著滯后現象的推測www.好了av.com。

In order to deeply reveal the smoothing mechanism of roller burnishing and to overcome the difficulty in the selection of the burnishing cross feed dependent mainly upon experiences and hand feel, the roller burnishing process is taken as an issue of plane-strain mechanics and the micro-plastic deformation area is determined on the basis of the Von-Mises yield criterion and by using the Boussinesq-Flamant solution. Then, the contact pressure distribution is obtained based on the Hertz contact theory, and the stress distributions in the burnishing tool and the workpiece are respectively revealed.

為深入了解滾柱滾壓表面光整機理日本一本亚洲免费区，解決目前滾壓量選擇完全憑經驗和手感的不足，將滾柱滾壓加工過程視為平面應變力學情形浮力国产在线，利用Boussinesq-Flamant問題的求解并根據Von-Mises屈服準則得出了滾壓局部發生微塑性變形的區域人人摸人人澡人人，根據Hertz接觸理論得出了滾壓接觸壓力分布及滾壓過程中工件和工具的應力分布。

The two definitions of dilatancy in slip line theory are clarified, and the generalized Mises yield criterion matching Mohr-Coulomb yield criterion in plane strain condition is put forward where the effect of dilatancy can be considered.

闡明了滑移線場理論中有關剪脹的描述97免费人妻视在线视频，推導了平面應變條件下考慮剪脹角影響并與Mohr-Coulomb準則精確匹配的廣義Mises準則九九成色视频在线观看，研究了剪脹對淺基破壞模式的影響。

Von Mises believed markets, like people, needed to be free from government meddling.

Von Mises 認為市場就像人一樣需要擺脫政府的干預狼友首页。

At one point, Hayek's former mentor, Ludwig von Mises, stormed out of a meeting.

有一次黄页视频免费在线看，哈耶克以前的導師－Ludwig von Mises－怒氣沖沖地離開了會場。

For other cases, the limit loads based on Mises criterion is proposed instead.

其它情況建議使用基于Mises準則的解91人妻论坛兴趣杂谈。

Then the principle equations of streamline in the general von Mises coordinate system are derived for the first time.

在三維流動情形亚洲小说图片综合在线专区，引入了兩個流函數η和ζ，并通過廣義von Mises變換日韩高清在线精品观看网站免费，首次導出了坐標系下的三個流線控制方程日韩网友自拍区在线观看网站。

In this paper, von Mises- Drucker -Prager yield surfaces are discussed.

在本文中午夜视频久久久久一区免费，討論了von Mises- Drucker -prayer屈服面。