One of the fine blanking methods is that in which the punch has a round edge and a small clearance.

精沖工藝方法的一種是使用圓形的刃口模具和小的間隙。

The program is the first of blanking-punching composite punch, then bending modulus composite production.

采取的工藝方案是先落料—沖孔復合沖壓，然后再彎曲亚洲自拍高清无码，采用復合模生產欧美成aⅴ人高清喷水。

The design method of faceplate oblique edge blanking die, die structure, punch structure and matrix structure were introduced in detail.

詳細介紹了面板斜刃沖裁模的設計方法和模具結構及沖裁凸凹模結構。

Engaged in spinning mold design, stamping die design (blanking die design, punch die design), and the spinning class product design (mainly the automobile belt pulley, water pump wheel, booster pump pulley, etc.), and rendering product process chart, product assembly diagram, right products, process analysis and process improvement, proficient in CAD, are familiar with PRO / E 3D modeling and design aspects of the work.

從事旋壓模具設計99尤物无码国产福利在线观看，沖壓模具設計（落料模具設計干逼视频，沖孔模具設計）以及旋壓類產品造型設計(主要是汽車皮帶輪，水泵輪殴美aaaav，助力泵帶輪等)99久久国产亚洲精品观看，繪制產品工序圖，產品組裝圖114毛片，對產品進行工藝分析以及工藝改善91三级片在线，精通CAD，熟悉PRO/E三維造型設計等方面工作欧美视频大全。

The punching, flanging ,blanking compound die made of polyurethane-rubber was introduced,including the design of insert and split punch block,polyurethane block and ejector pins.

分析了電器定位座聚氨酯橡膠模的結構特點自拍偷拍25页，介紹了聚氨酯橡膠模在沖孔、翻邊国产三级网片、落料復合模中的具體應用国产在线人人操，重點對鑲拼式凸凹模、聚氨酯塊和頂桿的設計進行了分析和闡述午夜福利在线视频观看在线，對同類模具的設計具有參考價值日韩资源在线观看快射视频免费。

The shaping course of Fine blanking is very complex. Material forms a local plastic cutting area between punch and bottom die, and brings violent plastic flow under the effect of press stress. The grad of stress and strain is great, and it is an unstable transmutation process that came through an elastic distortion, plastic distortion and cut rupture.

精沖成形過程非常復雜，材料在狹窄的凸真人黄色网站入口免费、凹模間隙附近形成了局部塑性剪切帶91精品熟女另类，在壓應力的作用下產生強烈的塑性流動，應力應變梯度很大偷拍播放，是一個經歷彈性變形欧美黄色网站视频免费1000、塑性變形和剪切斷裂的非穩態大變形過程。

But in practice, due to the condition and tradition, for both the blanking and punching, the usual way is to produce punch first and then the die plate, or in the opposite way, so the conversion between them is needed.

但在實際生產中4444www免费看，由于條件和習慣的原因亚洲视频热热，部分工廠采用不分落料、沖孔欧洲免费av，均是先制造凸模久久黄色视频看一下，再配制凹模，或者反之狼友精品在线，這樣就需要進行換算717欧美论理电影。

Parts of the Process Analysis、Process improvements、Die with a complete composite blanking process Piercing 国产乱伦合集、Expounded washers composite Die Blanking the overall structure and characteristics of the process, Should pay attention to the issue of sexual and assembly process ,Piercing the settlement sheet国产精品女A片爽爽免费视频下载、 And seam compound die punch slender easily broken、Hole coaxial hard to ensure the short life and die of technical problems.

通過對零件的工藝分析国产怕怕，改進了工藝方案一区精品在线，用一套復合模完成落料沖孔工序，闡述了墊圈沖裁復合模具的整體結構特點及工作過程欧美特黄A级高清免费大片A片l，應注意的問題和裝配工藝性日本人妻黄色网站。解決了薄板沖孔、沖縫復合模的凸模細長易斷欧美偷拍视频xxxx、孔的同軸度難以保證以及模具使用壽命短的技術問題。改進了落料各种作爱视频、沖孔a级毛片免费看久久久、沖縫的制作工藝，設計了一套新型復合沖裁模国产性爱欧美性爱在线播放，提高了工件的同軸度精度欧美全部A片免费观看，延長了模具的使用壽命。

In this paper, by using the electromagnetic forming unit developed by ourselves, the influence of various parameters such as the thickness of elastomer, the diameter of the punch, the value of sorap and the installation form of the punch on the minimum discharge energy of blanking were studied on the base of experiments.

本文在自行研制的電磁成形機上利用試驗方法国产精品激情欧美可乐视频99，研究了帶有傳力介質的電磁成形落料的傳力介質厚度亚洲欧洲一区二区三区久久、凸棋直徑，搭邊值及凸模安裝型式等黑人猛精品无码一区二区三区，對電磁成形落料最小放電能量的影響欧美大胆a级精品视频在线观看。