The rattling model of a one stage gear system is established,in which mass unbalance,speed fluctuation of driving shaft and backlash of the gear pair are considered.

在考慮不平衡質量jiuse200、主動軸轉速波動及齒側間隙的情況下，建立了單級齒輪傳動系統的拍擊振動模型人人操人人爽黄色。

Considering the torque fluctuation of the driving shaft and the existence of the backlashes in both gear pair and clutch, a lumped mass gear- rattling model is established.

在考慮主動軸驅動轉矩波動国产yyzz、齒輪副齒側間隙及離合器間隙的情況下，建立了同時含有離合器間隙和齒側間隙的齒輪傳動系統拍擊振動分析的集中質量模型视频se。

In addition, when roller gear when no meshing clearance between generates this kind of gear poles.

另外欧美牲交免费一级A片影院，當不朱輥齒輪之間無嚙合間隙時也會爆發這栽齒輪杠。

It has validated the system of high efficiency, safety, and stable quality. Zero- programming method can be used in NC process with fixed and limited parameters, such as gear grinding, gear shaper, and manufacturing of axis and disc parts.

零編程方法適用于編程參數和工藝參數固定美女扒开下边喷水黄网站、有限的數控加工5Ⅴ99COm，還可推廣于齒輪加工的磨齒、插齒免费看性爱，以及軸類污视频久久久、盤類等零件的加工。

Looking on form-grinding as a tooth of shaper, noncircular gear grinding method would be deduced by using noncircular gear tooth generated method in the shaping process.

提出了用成形砂輪展成磨削法磨削非圓齒輪的方法日韩最大的黄色网站，并給出了利用該原理進行數控加工數據計算的方法自拍偷拍视频区。

The points-line meshing gear is different from involute gear in choice of helix angle.

點線嚙合齒輪螺旋角β的選擇，改變了漸開線齒輪為湊中心距或者從優化角度來選取β值的情況毛片在。

The contacting simulative analytical model of a pair of herringbone gear used in warship was established,and let the result of calculation be compared with Hertz theory,therefore explained the accuracy,effectiveness and reliability of the contacting element on gear contact stress analysis.

建立了一對艦用人字齒輪接觸仿真分析模型十八禁无码R片在线观看，并將計算結果與赫茲理論比較，說明了接觸單元在齒輪接觸應力分析上的精確性国产精品久久久综合桃花网、有效性和可靠性黄色a片在线看。

The theoretical analysis results indicate that micro-gear based on new profile is better than involutes'gear in mechanical characteristics.

理論分析結果表明新齒廓的微型齒輪比漸開線齒輪有更好的力學性能。

Aside from the predictable top-gear kickdowns, the six-speed generally seemed to be in the right gear at the right time.

除了可預見的頂級齒輪kickdowns 人操人AV，六速一般似乎是正確的齒輪在合適的時間轻点肏我在线观看91。

If the bevel gear used in the processing module mid-point of the standard spur gear tooth milling cutter with big-deep into the alveolar knife milling, then the big-toothed on the "fat", little-endian tooth on the "thin."

如果在加工時采用傘齒輪中點模數的標準正齒輪銑刀以大端齒深將齒槽一刀銑成，那么大端齒形就&肥&清纯唯美亚洲综合五月，小端齒形就&瘦&亚洲色一色噜一噜噜噜性色av。