See if we can encourage their competition to undercut their competitors and save us a lot of mone

然后看看我們是否能通過鼓勵他們的競爭對手報出比他們更低的價格乱辈通奷系列视频。這樣我們就能省一大筆錢。

MethodsLFA was extended as far as possible toward the undercut area behind the mylohyoid ridge in 23 patients.

23例病人全口義齒修復時舌翼區盡量伸展至下頜舌骨嵴后的倒凹區內日韩激情影院无码视频。

In general, undercut technology is used to adapt the rolling precess requirement.

為了適應滾壓工藝的要求国产特a毛片，一般采用帶有沉割槽滾壓處理。

Reoxidation of the polysilicon sidewall prior to silicon nitride spacer formation exacerbates the undercut.

氮化硅隔離構造前進行多晶硅側墻的再氧化加劇了側凹国产精品新品厕所。

Aside from undrafted faces and the obvious undercut features, there are several other applications for side actions.

除了倒扣和無拔模角平面以外后插入黄色视频，這種方式還有一些其它的應用2021免费三级片。

Undercut is a small groove that can be lathed in advance at the end of the component .

退刀槽是指在螺紋終止處預先車出一個小槽。

Test results show 1 the fatigue strength of peened joints under overloading, in spite of lower than the fatigue strength of the non-overloading peened joints, is still greatly higher than the fatigue strength of as-welded joints; 2 In the range of lower stress level and longer life, ultrasonic peening method exhibit better results than TIG dressing; 3 Fatigue strength of the welded joints with defects (such as undercut at the weld toe) can also be improved greatly after peening treatment.

結果表明亚洲三级片久久91，超聲沖擊處理過的焊接接頭經過載后疲勞性能有所下降日批国产，但與原始焊態相比提高疲勞強度、延長疲勞壽命的效果仍然十分顯著91无码白浆丝袜在线播放；在低中應力水平手机日韩精品第一页在线观看免费、中長壽命區域，使用超聲沖擊法提高焊接接頭疲勞強度比TIG熔修法效果更好国模漏逼；超聲沖擊處理后AV午夜福利在线观看，含咬邊等缺陷的焊接接頭，疲勞強度同樣有較大的提高国产第二页。

2 What maximum depth of undercut is permitted in transverse splices of primary members ?

在主要構件中免费A级毛片在线视频观看，橫向接縫的咬邊最大允許多深？

The external undercuts can be further classified into inside and outside external undercut.

大概就是這個意思翻譯的不好湊活看吧

Use alternating transverse magnetic-field to control dragged arc , overcome weld undercut, and improve the appearance of weld.

所以控制電弧后拖是高速焊改善焊縫成形的關鍵欧美日韩三级在线。