Predicting the up-curl chip breaking of three-dimensional groove inserts;2. The database of judging chip break is founded, which is based on the characteristic of chip breaking curve.

通過切削試驗，獲得了刀具主偏角黄网站色视频免费观看下载、切削速度和工作材料牌號對切屑的極限進給量和極限背吃刀量的影響規律及其經驗公式，并根據切屑折斷曲線建立了判斷切屑是否折斷知識庫和切屑折斷預報系統。

Using the analytical method, this paper presents the formulas for the relation of the inner fleet angle and clearance between wound-on coils of mine hoist in func-tion of drum and rope diameters.

本文用解析法求出了以絞筒直徑高清在线观看国产亚洲AV、鋼絲繩直徑為函數的礦井提升設備繩弦內偏角和纏繩間隙關系的表達式，并按此繪制了供實際應用的曲線圖国产高清美女一级毛片久久。

Compass is accurate to two compass degrees with declination adjustment function to correct the difference between true north and magnetic north - uses global needle.

指南針指南針是精確到2度的偏角調整功能糾正與真北和磁北的差異-使用全球針网友自拍另类重口日韩AV。

Analyzing on the fault of local rubbing caused by compatible misalignment of rotors, a dynamic model for the rotor system with misalignment and rub-impact was established. Then the dynamic behaviors of this system, which varied with the values of parallel misalignment and declination, were investigated by using numerical integral method.

以水輪發電機組轉子系統為研究對象，針對剛性聯軸器綜合不對中引起轉子局部碰摩的問題少妇乱淫特黄A片，建立了機組轉子不對中–碰摩耦合故障的動力學模型和微分方程男人扒女人添高潮视频动态，并利用數值積分方法研究該系統隨不對中平行量和偏角參數變化的動力學行為。

By virtue of bifurcation diagrams, Poincaré maps, orbits, time histories and frequency spectrum diagrams, the nonlinear dynamic responses of the generator rotor and hydraulic turbine rotor with coupling faults were analyzed. The results confirmed rich nonlinear motions such as periodic motion and quasi-periods with different values of parallel misalignment and declination. Moreover, the process of rub-impact is so complex that many low frequencies with large amplitude are in the range of

通過分岔圖成熟女人牲交片免费、Poincaré截面圖丁香花高清在线观看、軸心軌跡圖、時域波形圖和幅值譜圖系統地分析了發電機轉子與水輪機轉子在耦合故障下非線性動力學響應美女艹网站免费，發現機組轉子系統隨不對中平行量和偏角變化存在周期運動和復雜的擬周期日本三级片网黄色，其碰摩過程非常復雜，機組故障特征頻率除主要在1倍頻外欧美pAAAA片，還在0.3~0.4倍頻處存在幅值較大的諧波分量天美三级片网站。

Have resolved the angle of deflection on the morning sun.

有偏角就解決了早上的日照。

By this means, the measuring of mileages, the direction of railway, the little partial angle, the altitude of rail surface can be given at the same time.

置鏡任意點人人在线人人操，每個曲線建立相對獨立的直角坐標系亚洲美女天堂网，同時完成里程丈量、線路方向福利一区首页、小偏角免费A级不卡在线毛片、軌面高程的測量久精品91区热。

Of course, the ancient rishis were aware of the tropical, season-based cycles of northern and southern declination paths of the Sun and used them also when appropriate.

當然，古代的印度圣哲是知道熱帶的特级黄色片天天，在適當?shù)臅r候也使用以季節為基礎的太陽偏角南比變化周期黄色网站A级。

The transformation of the yaw moment under differential brake and the impact of the slip ratio and road surface friction coefficient to the yaw moment were analyzed. The distribution method of the brake force was confirmed. After analyzing the observability of the control system, the state observer was designed, the evaluation of the side slip angle was completed and result of the evaluation wan validated.

本文分析了差動制動時整車橫擺力矩的變化情況，研究了滑移率和路面摩擦系數對橫擺力矩的影響中文字幕久久精品无码一区二区，確定了制動力的分配原則97无码人妻免费视频碰碰碰69，進行了控制系統的可觀性分析，并設計了狀態觀測器幸福宝网站官网站，完成了質心側偏角的估算并對此估算結果進行了驗證国产视频第1页。

Theoretical analysis and experimental results show that in shaping of copper fin, when the depth of cut is less than 2 mm, the feed is ranged from 0.5 to 3 mm, and side cutting edge angle is ranged from 20° to 50°, fin with height from 1.5 to 3 mm and thickness from 0.3 to 1.8 mm can be steadily formed.

理論和實驗研究表明：在紫銅材料的成形中，切削深度小于2 mm在线国产福利网址、進給量0.5~3 mm久久久久久AV无码免费网站动漫、刀具主偏角20°~50°范圍內，可以穩定地形成翅高1.5~3.0 mm五月综合婷婷久久狠狠、翅厚0.3~1.8 mm的翅片二色aⅴ国产热。