In addition, because of the interleaving of top and bottom nappes, there is no bump in the air, the finite width of spillways can be fully utilized, and flood discharging atomization caused by bump of nappes can be weakened.

而且樱桃视频下载ios，表免费视频黄片、深孔水舌在空中交錯穿插，不發生空中碰撞国在线se视频，可充分利用有限的溢流寬度影音先锋每日全部新资源，并減少因水舌空中碰撞而導致的泄洪霧化的增強。

At the same time, large angular acceleration will cause impact in the hydraulic system.

溢流緩沖主要是降低瞬時壓力沖擊999黄色com。建立相應的功率狀態方程欧美性爱激情图区。

Though analysis and comparison,the appropriate angular aperture of runner and the interrelationship between overflow and exhaust system were achieved for the circular die casting.

分析比較得出適合圓形壓鑄件澆注系統設計時的橫澆道張角夾角范圍，以及溢流槽與排氣槽之間位置尺寸相互影響的關系www.激情小说。

With the different distances between fissures and Laoheishan volcanic cone and the types of lava flows (sheet lava flows or small sub-overflows), the tension fissures show the different features.

隨著距離老黑山火山錐位置的不同和熔巖流的類型(如席狀熔巖流黄色视频观看免费、小規模次級溢流體)不同，張裂呈現不同的特征欧美在线艹。

A hydrodynamical model for oilspill simulation in archipelagic waters with multiple open boundary conditions is set up and simulation/forecast tests in Zhoushan dingpu Port are performed.

初步試驗表明花蝴蝶视频在线观看，模式重視了港域內許多重要的流體動力學特征，能模擬或預報海域內三維潮流18黄色网、風生流及其相互作用亚洲日韩精品不卡在线，并為溢油模擬提供實時流

The equipment provided in process are: jig sorting mainly to deal with overflow flotation, jigging in the coal and coal flotation tail mixed into the power plants, waste shipped to the Waste Dump, block coal jigging dehydration, floating Coal election at the end of filtration and hydraulic flow classification Desliming, dehydration through the belt to the Coal Wharf.

本設備所規定的工藝流程是：以跳汰選別為主，浮選處理溢流久久久免费性交毛片，跳汰中煤和浮選尾煤混合入電站国产极品在线观看无码迅雷下载，矸石運向矸石山，跳汰塊精煤脫水、浮選精煤過濾與水力分級底流脫泥亚洲黄的全免费在线观看、脫水通過皮帶運到精煤倉亚洲国产AV无码精品无广告。

At last, the configuration of a relief valve were improved, the cavitating flow simulation.

最后，對溢流閥閥芯形狀進行了改進日韩欧美中文字幕免费第一页，通過對不同結構的化實驗和噪聲測試国产精品黄色视频一，實驗結果與流場分析結果一致，改進后的閥氣穴強度和噪聲均得到降低十八岁以下禁看的黄片视频。

LIQUID FLOW MEASUREMENT IN OPEN CHANNELS BY WEIRS AND FLUMES.

NF X10-312-1986 用溢流堰和水槽法測量明渠中的液流激情小说视频。

At last, according to the effect of orifice configuration on the cavitation, the several poppet configurations of a relief valve were designed in order to suppress cavitation, the cavitating flow simulation for different configuration were performed and compared in ordet to find a optimal conriguration.

最后，針對閥口形狀對氣穴的影響欧美国产一级黄色。，為了抑制閥口氣穴国产欧美日韩视频在线，對溢流閥閥芯形狀進行了改進，設計了幾種不同的閥芯結構1级片在线观看，分別對不同的閥芯進行了氣穴流場分析和比較日本一区二区精品好黄，來尋求優化的閥芯結構。

Traditional plastic injection molding machine relies on constant rate pump in oil supply, and each action in the process of plastic injection may have different requirements on speed and pressure. The surplus oil flows back to the oil tank through the proportioning valve in the way of flooding adjustment. In the whole process, the rotation speed of motor remains unchanged, so the oil volume is fixed as well. Furthermore, the action is intermittent, and not of full load, so a great amount of oil is wasted.

傳統的注塑機是采用定量泵供油的一级aaaaaa黄片，注塑過程的各個動作對速度久久精品女人天堂A片、壓力的要求也不一樣，它是通過注塑機的比例閥采用溢流調節的方式將多余的油旁路流回油箱小视频无码专区网，在整個過程中操欧美性爱，電機的轉速是不變的，故供油量也是固定的国产一级黄色网站在线，而由于執行動作是間隙性的欧美丰满少妇XXXX性，也并不可能是滿負載的，因此定量供油就有很大的浪費空間免费囯产黄片无级A。